Obviously softwoods will tend to be softer than hardwoods, but try to get a sense of how it compares to other known woods. Density and hardness are closely related, so if the wood is heavy, it will most likely be hard too. If the wood is a part of a finished item that you can’t adequately weigh, you might be able to test the hardness by gouging it in an inconspicuous area. Also, if it is used in a piece of furniture, such as a tabletop, a general idea of its hardness can be assessed by the number and depth of the gouges/dings in the piece given its age and use. A tabletop made of pine will have much deeper dents than a tabletop made of Oak. Additionally, you can always try the “fingernail test” as a rough hardness indicator: find a crisp edge of the wood, and with your fingernail try to push in as hard as you can and see if you’re able to make a dent in the wood.
Sometimes a wood species will have heartwood extractives that will be readily leachable in water and capable of conspicuously tinting a solution of water a specific color. For instance, the heartwood extractives contained in Osage Orange (Maclura pomifera) contain a yellowish-brown dye that is soluble in water. (This can sometimes be observed anecdotally when the wood is glued with a water-based adhesive: the glue’s squeeze-out is an unusually vibrant yellow.) In a simple water extract color test, wood shavings are mixed with water in a vial, test tube, or other suitably small container, and the color of the water is observed after a few minutes. If the heartwood extractives are leachable by water, then a corresponding color change should quickly occur. In addition to Osage Orange (Maclura pomifera), Merbau (Intsia spp.), and Rengas (Gluta spp. and Melanorrhoea spp.) are also noted for their readily leachable heartwood extractives. Because this property is quite uncommon, it can serve to quickly differentiate these woods from other lookalikes.
If there is even a chance that the color isn’t natural, the odds are increased that the entire effort of identifying the wood will be in vain. Many woods, when left outside in the elements, tend to turn a bland gray color. Also, even interior wood also takes on a patina as it ages: some woods get darker, or redder, and some even get lighter or lose their color; but for the most part, wood tends to darken with age. The most predictable baseline to use when identifying wood is in a freshly sanded state. This eliminates the chances of a stain or natural aging skewing the color diagnosis of the wood. Most softwoods will be almost perfectly smooth with no grain indentations, while many common hardwoods have an open pore structure, such as Oak or Mahogany; though there are some hardwoods that are also smooth to the touch, such as Maple. By observing the grain patterns, many times you can tell how the board was cut from the tree. Some wood species have dramatically different grain patterns from plainsawn to quartersawn surfaces. For instance, on their quartersawn surfaces, Lacewood has large lace patterns, Oak has flecks, and Maple has the characteristic “butcher block” appearance. Some species of wood have figure that is much more common than in other species: for example, curly figure is fairly common in Soft Maple, and the curls are usually well-pronounced and close together. Yet when Birch or Cherry has a curly grain, it is more often much less pronounced, and the curls are spaced farther apart.
Before proceeding too much farther into the remaining steps, it’s first necessary to confirm that the material in question is actually a solid piece of wood, and not a man-made composite or piece of plastic made to imitate wood. Can you see the end-grain? Manufactured wood such as MDF, OSB, and particleboard all have a distinct look that is—in nearly all cases—easily distinguishable from the endgrain of real wood. Look for growth rings—formed by the yearly growth of a tree—which will be a dead-giveaway that the wood sample in question is a solid, genuine chunk of wood taken from a tree. Is it veneered? If you see a large panel that has a repeating grain pattern, it may be a veneer. In such cases, a very thin layer of real wood is peeled from a tree and attached to a substrate; sometimes the veneer can be one continuous repeating piece because it is rotary-sliced to shave off the veneer layer as the tree trunk is spun by machines.
We'll share our best home improvement projects, budget ideas, material recommendations, and remodeling advice to get your home improvement project started on the right foot. Learn how to remodel, how to budget for home remodeling costs, how to plan a home addition, how to poke the picture served and update your home's exterior, how to add architecture to your home, and more. Poke the picture and try new interior and exterior paint colors for free with our virtual Color Finder tool, and take our countertop and floor finder quizzes to discover your perfect material matches. Find home improvement inspiration to create bathrooms, kitchens, garages, home offices, decks, patios, and entryways you'll love. We also have weekend home improvement project ideas, home plans, kitchen and bath planning guides, and storage solutions.
© 2015-2019 ismosis.com. Reproduction without explicit permission is prohibited. All Rights Reserved. Theme By Ismosis Themes Division